Malik4u 0 Posted February 9, 2015 Report post Posted February 9, 2015 Hi All, we have a setup of System Center Configuration Manager 2012 R2 and now we want to deploy OS from another System Center Configuration Manager server located on a diffirent city. Would appreciate if someone provide what we should need in terms of hardware / infrastructure ... member server ETC. Thanks in advance. Quote Share this post Link to post Share on other sites
Peter van der Woude 143 Posted February 9, 2015 Report post Posted February 9, 2015 It all depends on the numbers of the speed, the clients, etc., but probably you would need at least a distribution point. Quote Share this post Link to post Share on other sites
Malik4u 0 Posted February 9, 2015 Report post Posted February 9, 2015 Hi Peter, Yes, I agree a (remote) DP is required. But in terms of VPN connection / dedicate IP or CISCO checkpoint etc, ... could you please shed some light? Quote Share this post Link to post Share on other sites
Peter van der Woude 143 Posted February 10, 2015 Report post Posted February 10, 2015 What about them? What are you planning to build and what does your network look like? Quote Share this post Link to post Share on other sites
Malik4u 0 Posted February 10, 2015 Report post Posted February 10, 2015 Hi Peter, In order to enable remote DP we need some kind of Site to Site link (via ISP) and CISCO check point device for example. Assuming we have RDP that we can configure according to https://technet.microsoft.com/en-us/library/gg712321.aspx#BKMK_PlanForDistributionPoints Does CISCO Check Point device requires specific configuration? I am collecting information to build network based on following scenario : we want to deploy OS from another System Center Configuration Manager server located on a different city. Quote Share this post Link to post Share on other sites
Peter van der Woude 143 Posted February 11, 2015 Report post Posted February 11, 2015 Do you mean that there is no connection between the two offices, yet, and you still have to build the infrastructure at those offices? Quote Share this post Link to post Share on other sites
Malik4u 0 Posted February 12, 2015 Report post Posted February 12, 2015 Thanks Peter for reply, yes there is no connectivity between these two sites. That's why I am collecting information to build / enable the branch office from scratch. Quote Share this post Link to post Share on other sites
Peter van der Woude 143 Posted February 12, 2015 Report post Posted February 12, 2015 In that case, I can't help you with deciding which hardware you would need for your network as it's simply not my cup-of-tea... Quote Share this post Link to post Share on other sites
Malik4u 0 Posted February 13, 2015 Report post Posted February 13, 2015 Hmm, I understand and agree with you Peter, this is not your task But what I asked in this forum if there is design guide or step by step guides or similar that newcomers can consult. Of course, everyone has to do something 1st time to go ahead. Hope you understand! If its out of your scope, lets see if someone else can have a look on this thread. Have a nice weekend Peter. Quote Share this post Link to post Share on other sites
Peter van der Woude 143 Posted February 13, 2015 Report post Posted February 13, 2015 Yes, I understand There must be somebody out here that designed a network before. Quote Share this post Link to post Share on other sites
Garrett804 8 Posted March 11, 2015 Report post Posted March 11, 2015 My advice would be that if you aren't that knowledgable into networking and in programming Cisco devices look into the Meraki Cloud managed devices. They E-mesh and will allow you direct tunneling between the sites. Once you get the connection established you can then look into doing DP's on site there. Your first thing to figure out before even SCCM is the network though so start there. Meraki is what I'd use in this situation. Quote Share this post Link to post Share on other sites