Jump to content


matt1234

UEFI formatting issue on replacement surface devices

Recommended Posts

Hi,

 

We having been deploying Surface devices for sometime now using SCCM R2 SP1 CU3, followed the guides posted here, and have had good luck with these for sometime now. We recently however had to warranty a few surface pro 3 devices for our users, and we are having alot of trouble getting these to format correctly, before failing the task sequence.

 

Note: There have been 0 changes to the Task sequence for sometime, and we are able to image new units.

 

Model: 256GB Surface Pro 3 back from service

 

Prep for imaging:

- Disable Secure boot/Clear all keys

- Disable TPM

- Secure Erase SSD (via surface data eraser tool provided by MS)

- Created Offline (USB) Media

 

Imaging:

-SP3 starts and loads files to boot into WinPE

-Machine name step pops up as normal

 

Next Step,

 

Format and Partition Disk (UEFI) - Hangs and eventually fails out stating that it cannot format the disk (log file attached).

 

This problem remains true if I attempt to image via Offline media, with RMA units only. I left one of the RMA'd devices stock, joined the domain, loaded client, added to a collection and pushed the task sequence for testing/troubleshooting, and I took another Surface we've had on hand for a while, and ran the offline USB image through n through with no issues.

 

The one thing that does stick out, is the internal hard drive vendor. From what we have seen, the majority of the surface units have a Samsung SSD, whereas the RMA units have a Hynix based SSD built in. Being it's a hard drive, the storage drivers should be the same for boot image being the chipset is the same, and vendor should not matter being the same sata protocol. Other than that, I cannot figure out a reason as to why this is happening. trying a new USB stick had no change as well.

 

 

Has anyone run into or seen anything this before?

 

Update: I found this article, that is basically pointing out the same problem, sadly no solution though- https://social.technet.microsoft.com/Forums/en-US/5a17cf36-d208-4264-ab66-9e483054bcc9/sccm-osd-task-sequence-stuck-at-formatting-c?forum=configmanagerosd

 

- Another kicker, I was able to bring the trouble unit back to the factory image using the recovery USB media created earlier. I went ahead and attempted to image this thing the same way as the other unit- Join domain, add to collection, push TS to unit. Even THAT has failed at the exact same point, where it was no issue for the other one. I'll mess around a little more tomorrow.

Share this post


Link to post
Share on other sites


where[s your log file ?

Share this post


Link to post
Share on other sites

can you hit f8 to open command line and then do a diskpart? I'd be interested in seeing if it can list your volumes.

I'm thinking that it doesn't have the disk drivers to be able to access the drive.

 

http://happysccm.com/2014/12/16/format-failed-0x80070057-during-task-sequence/

 

also, you might need the KB and add it to your boot wim:
Win10ADK-Hotfix-KB3143760.exe

Share this post


Link to post
Share on other sites

Are you using MDT Boot Images? If not my suggestion would be integrate MDT and use them. You'll have alot more success, all you'll need to do is add the Surface Network Drivers to the them. Storage is covered OOB in most cases (Surfaces definitely)

 

I am imaging SP3 and 4 devices with 1602 and MDT 2013 Update 2........Zero Issues.

Share this post


Link to post
Share on other sites

I know this is way late, time has gotten the best of me...

 

So it turns out, that the issue according to a MS engineer our rep had referred us to, the intel "iastore.sys" driver for 6th generation (Skylake) CPUs (provided by Lenovo) conflicts with the surface pro NIC driver. We ended up creating a separate boot image for surface pro and book devices, and have called it done until we can re-explore this later.

 

I didn't want to leave this one open ended, so hopefully if anyone runs across this post, it will be of some help/direction.

  • Like 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...