Jump to content


Recommended Posts

After upgrading to 1511 and ADK win10 and running the patch kb314370,

F12 a client and get "No boot file name available".

Cannot get F8 to open a cmd prompt for support logs either, yes it is enabled.

Both the new (x86 and x64 from ADK) boot images are distributed and have WinPE 10 drivers.

PXE is enable and advertised by the DT.

SMSPXE.log on the server is not even being populated.

Previous to this upgrade, we could PXE boot, now we can't.

 

Thank you for any help!

KACouillard

Share this post


Link to post
Share on other sites


I just found this in Monitoring Componet Status:

Critical SMS_MP_CONTROL_MANAGER

ERROR SMS_MP_CONTROL_MANAGER

MP Control Manager detected management point is not responding to HTTP requests. The HTTP status code and text is 500, Internal Server Error.

Possible cause: Management point encountered an error when connecting to SQL Server.

Solution: Verify that the SQL Server is properly configured to allow Management Point access. Verify that management point computer account or the Management Point Database Connection Account is a member of Management Point Role (msdbrole_MP) in the SQL Server database.

Possible cause: The SQL Server Service Principal Names (SPNs) are not registered correctly in Active Directory

Solution: Ensure SQL Server SPNs are correctly registered. Review Q829868.

Possible cause: Internet Information Services (IIS) isn't configured to listen on the ports over which the site is configured to communicate.

Solution: Verify that the designated Web Site is configured to use the same ports which the site is configured to use.

Possible cause: The designated Web Site is disabled in IIS.

Solution: Verify that the designated Web Site is enabled, and functioning properly.

Possible cause: The MP ISAPI Application Identity does not have the requisite logon privileges.

Solution: Verify that the account that the MP ISAPI is configured to run under has not been denied batch logon rights through group policy.

For more information, refer to Microsoft Knowledge Base article 838891.

And the site server Event Log:

Warning WAS

The description for Event ID 5009 from source Microsoft-Windows-WAS cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.

If the event originated on another computer, the display information had to be saved with the event.

The following information was included with the event:

SMS Management Point Pool
3824
fffffffe

And this in the Event Log:

Error DistributedCOM

The application-specific permission settings do not grant Local Launch permission for the COM Server application with CLSID
{4D581488-83B4-46AF-921C-275B583B691C}
and APPID
{AD65A69D-3831-40D7-9629-9B0B50A93843}
to the user NT AUTHORITY\LOCAL SERVICE SID (S-1-5-19) from address LocalHost (Using LRPC) running in the application container Unavailable SID (Unavailable). This security permission can be modified using the Component Services administrative tool.

Share this post


Link to post
Share on other sites

have you tried reinstalling the Management Point role ?

Share this post


Link to post
Share on other sites

I just fixed the MP issue (ERROR SMS_MP_CONTROL_MANAGER) by changing the Management Point Connection Account from use the computer account to domain service account.

 

Still unable to PXE boot.

 

On a client I am trying to PXE boot, F4 to get a command prompt. ipconfig /all results:

Host Name: (blank)

Primary Dns Suffix: (blank)

Node type: Hybrid

IP Routing Enabled: No

WINS Proxy Enabled: No

Share this post


Link to post
Share on other sites

  • Steps I tried with No success:

      1. Disable PXE support on all (old and new) boot images

    • Disable PXE support on DP

  • Remove WDS role

Reboot server

Enable PXE support on two new boot images (x64 and x86 winpe ADK Win10)

Enable PXE support on DP

Wait for WDS role to be installed

Redistribute two new boot images to DP

Verify RemoteInstall folder has been populated

F12 a client – no, same error PXE-E53 No boot file name available

Share this post


Link to post
Share on other sites

I removed, and reinstalled the MP. I also added DHCP scope options even though the client and server are on the same subnet.

 

The good news:
a. the MP is healthy online again
b. the smspxe.log is populating again
c. the client gets an IP and downloads the wdsnbp, then errors.
The bad news:
a. errors in the smspxe.log (see below)
b. the client error: The BCD from the PXE server does not contain a valid operating system. Ensure the server has boot images installed for this architecture.
File:\\Tmp x86x64(<numbers>).bcd
Error code: 0x0000098
Severity Type Site code Date / Time System Component Message ID Description
Information Milestone C10 6/22/2016 2:08:52 PM CSD10.CSD.LOCAL SMS_MP_CONTROL_MANAGER 4629 Component Status Summarizer detected that the availability of component "SMS_MP_CONTROL_MANAGER" on computer "CSD10.CSD.LOCAL" has changed to Online.
PXE::MP_InitializeTransport failed; 0x80004005 SMSPXE 6/22/2016 2:08:30 PM 6936 (0x1B18)
PXE::MP_LookupDevice failed; 0x80004005 SMSPXE 6/22/2016 2:08:30 PM 6936 (0x1B18)
PXE::MP_InitializeTransport failed; 0x80004005 SMSPXE 6/22/2016 2:08:30 PM 6936 (0x1B18)
PXE::MP_ReportStatus failed; 0x80004005 SMSPXE 6/22/2016 2:08:30 PM 6936 (0x1B18)
PXE Provider failed to process message.
Unspecified error (Error: 80004005; Source: Windows) SMSPXE 6/22/2016 2:08:30 PM 6936 (0x1B18)
94:57:A5:01:8C:40, B3B369FF-F4C2-11E4-A609-7070990000FF: Not serviced. SMSPXE 6/22/2016 2:08:30 PM 6936 (0x1B18)
Prioritizing local MP http://CSD10.csd.local. SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)
RequestMPKeyInformation: Send() failed. SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)
Failed to get information for MP: http://CSD10.csd.local. 80004005. SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)
reply has no message header marker SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)
PXE::MP_LookupDevice failed; 0x80004005 SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)
Prioritizing local MP http://CSD10.csd.local. SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)
RequestMPKeyInformation: Send() failed. SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)
Failed to get information for MP: http://CSD10.csd.local. 80004005. SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)
reply has no message header marker SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)
Failed to send status message (80004005) SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)
Failed to send the status message SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)
PXE::MP_ReportStatus failed; 0x80004005 SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)
PXE Provider failed to process message.
Unspecified error (Error: 80004005; Source: Windows) SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)
94:57:A5:01:8C:40, B3B369FF-F4C2-11E4-A609-7070990000FF: Not serviced. SMSPXE 6/22/2016 2:08:34 PM 6936 (0x1B18)

Share this post


Link to post
Share on other sites

so are both architecture boot images distributed, and enabled for PXE and attached to the task sequence you are testing ?

Share this post


Link to post
Share on other sites

both x86 and x64 winpe boot images contain two net drivers (an Intel and a Realtek), distributed and enabled PXE. Only one is attached to the task sequence. In this case I have a win10 OS, so I attached the x64 boot image.

Share this post


Link to post
Share on other sites

Here are the smspxe.log results when I F12 a client, and it replies PXE53 - No boot file name available.

The MAC not serviced is the client I am attempting to boot.

 

Prioritizing local MP http://CSD10.csd.local. SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)
RequestMPKeyInformation: Send() failed. SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)
Failed to get information for MP: http://CSD10.csd.local. 80004005. SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)
reply has no message header marker SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)
PXE::MP_LookupDevice failed; 0x80004005 SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)
Prioritizing local MP http://CSD10.csd.local. SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)
RequestMPKeyInformation: Send() failed. SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)
Failed to get information for MP: http://CSD10.csd.local. 80004005. SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)
reply has no message header marker SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)
Failed to send status message (80004005) SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)
Failed to send the status message SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)
PXE::MP_ReportStatus failed; 0x80004005 SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)
PXE Provider failed to process message.
Unspecified error (Error: 80004005; Source: Windows) SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)
94:57:A5:01:8C:40, B3B369FF-F4C2-11E4-A609-7070990000FF: Not serviced. SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)

Share this post


Link to post
Share on other sites
Prioritizing local MP http://CSD10.csd.local.  SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)

RequestMPKeyInformation: Send() failed. SMSPXE 6/23/2016 8:33:10 AM 3404 (0x0D4C)

still having issues contacting the Management point, take a look at this post to see does it help you resolve your problem

 

https://www.windows-noob.com/forums/topic/7281-management-point-pxe-boot-error-80004005-after-sp1-upgrade/

Share this post


Link to post
Share on other sites

Yes that is the root of the issues for sure. My EP defs are not getting to clients anymore either. This is a great article and I did all these steps yesterday. It made a brand new remoteinstall folder but did not fix anything.

 

  • untick the enable PXE checkbox on the distribution point. Answer yes that you want to remove the Windows Deployment service.
  • remove boot images from your distribution point
  • After 5 minutes delete %windir%\temp
  • check with server manager. If WDS is done uninstalling there is a reboot pending. Reboot.
  • check if the remoteinstall folder is located on your system. If it is delete it. If it fails to delete due to permission issues with the SMSTempBootFiles path, delete all folders except that one and then rename the remoteinstall folder something else.
  • reboot
  • Add the PXE point again by checking the box on the distribution point properties. Check the distrmgr.log and see if the remoteinstall folder reappears..
  • Replicate the boot image to the DP again.

Share this post


Link to post
Share on other sites

Still get this error when f12 a client PXE53: No Boot file name available. Here are the latest steps I have done, without success.


  • Uncheck PXE and Multicast on the distribution point. Answer yes that you want to remove the Windows Deployment service.
  • remove all boot images from your distribution point
  • Wait until WDS is gone, then rename %windir%\temp to ­_old
  • If WDS is done uninstalling there is a reboot pending. Reboot.
  • Rename RemoteInstall folder to _old
  • This time I am going to delete all boot images from OS/Boot Images. I am trying to make the RemoteInstall folder recreate without any boot images. Maybe this is why the “Invalid file version found” errors in smspxe.log. Example: Failed to retrieve the version of file 'C:\RemoteInstall\SMSTempBootFiles\C1000063\WINDOWS\Boot\PXE\pxeboot.com'. Error code: 0x80004005
  • reboot
  • Select PXE and Multicast on the distribution point. A new RemoteInstall folder should be created and WDS. Look at the distrmgr.log and smspxe.log. May have to restart WDS service.
  • Create new boot images
  • Distribute the boot images to the DP again.
  • This all sounded good but did not work. Next, I am going to delete the boot images, uninstall ADK10 and install ADK 10 RTM (older version), then recreate the boot images. – No this did not work either.
  • Next? I think this is the root of the problem:

Mpcontrol.log:


Initialization still in progress. SMS_MP_CONTROL_MANAGER 6/24/2016 3:24:19 PM 3784 (0x0EC8)


Beginning periodic tasks. SMS_MP_CONTROL_MANAGER 6/24/2016 3:24:49 PM 3784 (0x0EC8)


RetryWINSOperationIfNecessary: No need to retry. Returning. SMS_MP_CONTROL_MANAGER 6/24/2016 3:24:49 PM 3784 (0x0EC8)


RetryDNSPublishingIfNecessary: No need to retry. Returning. SMS_MP_CONTROL_MANAGER 6/24/2016 3:24:49 PM 3784 (0x0EC8)


Completed periodic tasks. SMS_MP_CONTROL_MANAGER 6/24/2016 3:24:49 PM 3784 (0x0EC8)


SSL is not enabled. SMS_MP_CONTROL_MANAGER 6/24/2016 3:24:49 PM 3784 (0x0EC8)


Call to HttpSendRequestSync failed for port 80 with status code 500, text: Internal Server Error SMS_MP_CONTROL_MANAGER 6/24/2016 3:24:49 PM 3784 (0x0EC8)


Sent summary record of SMS Management Point on ["Display=\\CSD10.csd.local\"]MSWNET:["SMS_SITE=C10"]\\CSD10.csd.local\ to \\CSD10.csd.local\SMS_C10\inboxes\sitestat.box\b6n3dr1i.SUM, Availability 1, 303725564 KB total disk space , 23328884 KB free disk space, installation state 0. SMS_MP_CONTROL_MANAGER 6/24/2016 3:24:49 PM 3784 (0x0EC8)


Successfully performed Management Point availability check against local computer. SMS_MP_CONTROL_MANAGER 6/24/2016 3:24:49 PM 3784 (0x0EC8)


Initialization unsuccessfully completed within the allowed interval. SMS_MP_CONTROL_MANAGER 6/24/2016 3:24:49 PM 3784 (0x0EC8)


Share this post


Link to post
Share on other sites

Microsoft professional support just solved this issue. They removed the MP, rebooted, ran a program called "ccmclean.exe" and then installed the MP. No more errors in the MPcontrol.log and PXE boot works!

  • Like 2

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...