Jump to content


Sign in to follow this  
JHFerry

SCCM 2012 R2 T450 Non fatal error 0x80072ee7

Recommended Posts

I am having a really tough time getting an image down to a T450 x64. Some specs first:


DP = SCCM 2012 R2, WIndows 2008 R2


Boot Image, x64 Version 6.3.9600.16384


Deploying OS Windows 7 SP1 x64



Task Sequence:


post-19923-0-58551200-1439823525_thumb.jpg


Driver Pack (from Lenovo)



post-19923-0-68771800-1439823437_thumb.jpg


Nic driver in boot image:




post-19923-0-22100400-1439823527_thumb.jpg



First off, I needed to plug a USB KB in because f12 doesn't seem to be detected on these. My tasks run all the way through "Setup Windows and Configuration Manager" At that point it needs to reboot. Once it boots it runs through setting up Windows and dies at applying settings. The error "Windows could not configure one of more components. To install Windows, restart the computer and then restart the installation"



My SMSTS.log looks fine until the end:


unknown host (gethostbyname failed) TSManager 6/16/2015 11:05:57 AM 1940 (0x0794)


sending with winhttp failed; 80072ee7 TSManager 6/16/2015 11:05:57 AM 1940 (0x0794)


Error calling message lib Send(). Code 0x80072ee7 TSManager 6/16/2015 11:07:15 AM 1940 (0x0794)


Non fatal error 0x80072ee7 in sending task sequence execution status message to MP TSManager 6/16/2015 11:05:09 AM 1940 (0x0794)


Execution engine result code: Reboot (2) TSManager 6/16/2015 11:07:15 AM 1940 (0x0794)



From everything I read it looks like a Nic issue but I can't figure it out. Are my tasks ok? How can I verify I am using the right Nic and it is applying? My sense is I am not applying the drivers correctly or my partitions are wrong somehow. Of course, this is also my first experience with UEFI bios. I have tried the Legacy setting with similar results.



Also, from an F8 prompt I have IP all the way until I reboot.


post-19923-0-68771800-1439823437_thumb.jpg

post-19923-0-58551200-1439823525_thumb.jpg

post-19923-0-22100400-1439823527_thumb.jpg

Share this post


Link to post
Share on other sites

This could also be caused by spanning tree port fast not being enabled on the switch, not sure if that is your issue.

It's a NIC issue, posting the Lenovo response for others:first, remove all drivers from your boot image. i missed in your first post you're using pe version 6.3.9600.16384, which is windows 8.1/winpe 5.

download the winpe5 driver pack from here : http://support.lenovo.com/us/en/downloads/ds102312

in that driver pack contains the NIC driver for windows 8.1/winpe5, which is e1d64x64. import that into sccm and add it to your boot image. distribute to your DP.

next, download the windows 7 64 bit driver pack from here: http://support.lenovo.com/us/en/downloads/ds102111

import these drivers into sccm and create your driver package that will contain them. distribute to your DP.

in your task sequence, apply driver package and assign it your newly created t450 package. you should be able to leave it where it is per your screenshot.

use this wmi query to target: SELECT * FROM Win32_ComputerSystemProduct WHERE Version='ThinkPad T450'

that should hopefully take care of everything!

Although I can't get SCCM to inject those drivers into a package. Keep getting an error, "Some packages could not be updated"

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
Sign in to follow this  

×
×
  • Create New...