Skip to content

Deploy XP

  1. Started by Andy Turner,

    I captured an xp image using MS Virtual PC and a Capture Media that I created. Then used that image to create a task sequence that I have advertised to all Unknown computers. When I run the TS on my nw8240 everything seems to run correctly as far as installing drivers, partitioning the disk, and installing XP but when the laptop reboot I get a BSOD when Windows tries to load and the it just reboots again. Am I missing a driver? Any help would be greatly appreciated.

    • 2 replies
    • 4.2k views
  2. Started by Adminoob,

    I have several computers that have XP Pro 32bit on them, but the machine architecture is actually x64; I have successfully captured wim images from these machines using either x64 or x86 boot images, should I ALWAYS use x64 boot images to capture on X64 arch. (even when the OS I'm capturing is 32bit?)

    • 2 replies
    • 8.3k views
  3. Started by RhoSysAdmin,

    I'm trying to work through the XP build and capture tutorial with my SCCM 2007 R3 system. The first suspicious thing is that the workstation identifies it's architecture as x64 at the bios, but then it will load my boot image. I see the SCCM 2007 splash screen, but then after a minute it reboots. I thought it might be that it wasn't a bare metal workstation, so I wiped the existing volume on it, but that didn't make a difference. I enabled command support, but F8 doesn't get me a command prompt. I've updated the distribution point for my OS install image, and double checked my task sequence against the tutorial in this forum. I don't know where to look next. …

  4. I have SCCM R3 with MDT 2010 Update 1 Q1: Should I receive the Windows Setup Wizard on my reference machine post Image Capture? Q2: Can the State Capture, State Restore & Gather Logs Groups within TS be disabled is User State Capture is not required? I am trying to build and capture a Windows XP SP2 reference machine in order to deploy. I am using the MDT Client Task Seq - which successfully completes and captures a .wim image - however post capture I am receiving a Windows Setup Wizard asking for all the settings that I have already specified within the Task Sequence or the SysPrep file along with Unattend.txt I followed the MDT SCCM TS guide to customis…

  5. In my task sequence I used "Apply Driver Package" to install the drivers, but when I log in, none of the drivers are installed. The drivers are however being copied across to the PC, and when I do a local search the driver is picked up and installed. Shouldn't these drivers be automatically picked up (and installed)? What am I doing wrong?

    • 1 reply
    • 4.1k views
  6. Hello all, i've been using SCCM to Deploy a image of our XP Machines. Works pretty well except for one thing. We identify our machines by our site codes, which differ for each country. Now i want to deploy software during my OSD TS only to choosen countries. The machine is named and joined a domain already. I want it to be decieded by the computer name it has. What I tried is using if normal TS Variable _SMSTSMachineName equals "XXX%" where the XXX identifies the site, followed by model and our own unid. That did not work as he could not find a match here. I've tried on reading up on MS and other forum but somehow i do not get further with that question. Ma…

    • 3 replies
    • 6.5k views
  7. Hi All, I'm trying to do an image capture without first sysprep'ing the device. (Basically how I used ghost when I wanted to get a backup of a machine) My task sequence is basically this restart in win pe use toolkit package (the mdt toolkit) set variable ComputerBackupLocation capture image (%scriptroot%\ztibackup.wsf Everytime I an error on my capture image step that says 0x00000001. SMSTS.log says failed "incorrect function" I opened up the share with no change, i added my domain admin account on the capture image step and the error goes to 0x80004005 (i'll have to double check on that code) My MDT package was created by importing a mdt task seque…

    • 3 replies
    • 12.5k views
  8. Started by StueyT,

    Hi all, I'm having an issue with OSD and the PXE boot. If I am using a machine that PXE has never seen before, where I've imported the MAC and machine name into the SCCM console, then it'll boot no problem. However, if I'm using a machine that has previously had a OSD run before, it'll abort any PXE boot I try. This is after I've deleted all trace of the machine from SCCM, re-imported the MAC info, and cleared the last PXE advertisement. Sometimes, if I turn the machine off for an hour and then try PXE again, it'll work, but sometimes that wont. I have 2 test machines here that have been aborting under PXE boot for the last 24 hours. Any idea?

    • 1 reply
    • 4.4k views
  9. Started by Vancouverite,

    I'm finding that I'm having to restart the WDS service on my SCCM servers far, far too often for my liking. Initially, in my test/lab environment, I encountered that problem that I know many other people have seen where, after reimaging the same machine multiple times, eventually it fails to pxe boot (PXE Boot Aborted) and clearing the last PXE advertisement doesn't resolve this. In that scenario stopping and restarting WDS would work and after that imaging would continue as normal. I put this behaviour down to the fact that the same small number of machines were being imaged and reimaged multiple times over a short period of time. But now that SCCM is being u…

  10. Started by lord_hydrax,

    Hi, I am having absolutely no luck deploying Audio Drivers for any HP machines as part of OSD, specifically in our environment for the 6930p/8440p/6550b Notebooks and 7900/8000 desktops. I deploy other drivers with pretty much no issues using the 'Bad Driver' method by having them in a package running a setup.exe -s command to install. I try this with the Audio drivers and it never works. Though once the OSD completes and I log on for the first time, if I run the same silent install command it works just fine. I have tried running the command in Full OS and Win-PE mode, and also tried injecting using Apply Driver Package with no success. What are othe…

  11. Started by oslsd,

    I would like to know if it would be possible to run the OSDWinSettings.exe command in a Run command line task sequence. I have not been able to find any examples of the syntax to do this and there does not appear to be any way to modify the Apply Windows Settings TS. My only purpose for running this command is to automatically name the workstation (XP SP3) based on the AssetTag value in the Bios. This works now but I always get an error about the administrator password could not be changed when using the Apply Windows Settings TS. I do not wish to remove the Administrator PW from my image. If I could just find a script to query the bios and write the value to the sys…

    • 1 reply
    • 5.3k views
  12. Started by NGrant,

    I've working on getting a full deployment working from SCCM 2007. I've gotten through PXE booting and the deployment works up until it reboots the first time goes into Windows Setup. I get a message on the screen that says "The file nvrd32.sys could not be found. Press any key to continue" If I press any key the machine reboots and goes back to the same exact spot. Not sure how to get this problem fixed.

  13. I need to setup a new imaging process using SCCM and Unfortunately we still use XP (Won't be migrating to Win7 anytime soon either) - I need to setup a process to image new "bare metal" PCs using ZTI and PXE boot. Has anyone done this before? The only guides I can find online are for Win7/Vista or refer to migrating to Win7. Any help would be grately received!

    • 2 replies
    • 4.5k views
  14. Started by maktoum,

    Hi I need clarification about client certificate ..., Before capture windows xp sp3 image ... - I joint machine to domain - then I install client on machine - after finish installing client I disconnected from domain and network - then I delete sms certification by going through these steps: 1- start mmc, add certificate snap in. 2- select local computer. 3- from the root open folder personal, then computer and thats where the cert should be select it and press delete. 4- Close. after that I start capture the image by running SMS boot-able CD then I check the certifications in the PC which I capture…

    • 4 replies
    • 8k views
  15. Hi Everyone, we just migrated our OSD over to our SCCM server and I'm trying to get imaging working for our vmware virtual machines (ESX). I have already imported the vmware drivers and made them into a package. The package has been added to all DPs and Boot Images and I've updated the distribution points. I pxe boot the slice, start the task sequence but as soon as it gets to the partition/format part it just dies and reboots the workstation. When you build XP normally with the CD this happens if you haven't pressed F6 previously and mounted the 'floppy' drive with the vmware SCSI drivers so i'm assuming this is where it's failing. The problem is, I've already added the …

    • 1 reply
    • 6.2k views

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.